Prns
← Boards

Beta

Flash a Personal Hopspot

Choose your device to get started. Flash a signed release from your browser, or follow the setup guide for your board.

Selected target

Heltec Wireless Stick Lite V3

ESP32-S3FN8 + SX1262

Heltec Wireless Stick Lite V3
Installation mode

Prepare the board

The flasher will try the board's cataloged automatic reset strategy first.

  1. 1Use a USB data cable connected directly to this computer, and close serial monitors using the board.
  2. 2When asked, choose this board's serial port. Port names come from the chip rather than the board, and different boards can share the same chip, so if you're not sure which port is which, unplug everything else first.
  3. 3If automatic connection fails, hold BOOT, tap RESET, release BOOT, then restart the complete connect-and-flash step.

Review and verify

Waiting
  1. 1Confirm the exact board pictured above.
  2. 2Prepare the release. Every part is downloaded and verified before the flasher touches your device.
  3. 3Connect with a USB data cable and choose the board's serial port.
  4. 4Flash. Each part is verified again on the device, then the flasher requests a board restart.

No full-chip erase. Every published byte is signature- and hash-verified before device access.

Checking this browser for secure Web Serial support before release preparation is enabled.

Confirm the exact board before preparing its sparse serial flash plan.

Change board

Each card shows the current support status and next steps for that device.

Heltec LoRa 32 V4 (S3R2)flashable

ESP32-S3R2 + SX1262 (Quad PSRAM)

Flash →
Heltec LoRa 32 V4 (S3R8)flashable

ESP32-S3R8 + SX1262 (Octal PSRAM)

Flash →
Heltec Vision Master E290-HFflashable

ESP32-S3R8 + HT-RA62-HF/SX1262 (Octal PSRAM)

Flash →
Heltec Wireless Stick Lite V3flashable

ESP32-S3FN8 + SX1262

Selected
LilyGO T-Beam Supremeflashable

ESP32-S3 + SX1262 + AXP2101

Flash →
Seeed XIAO ESP32-C6flashable

ESP32-C6

Flash →
LilyGO T-Echoflashable

nRF52840 + SX1262

Flash →
Heltec Mesh Node T114flashable

nRF52840 + SX1262

Flash →
Heltec MeshPocket 5000 mAhflashable

nRF52840 + SX1262 + 2.13-inch e-ink

Flash →
Heltec MeshPocket 10000 mAhflashable

nRF52840 + SX1262 + 2.13-inch e-ink

Flash →
Heltec Mesh Node T096flashable

nRF52840 + SX1262 + KCT8103L PA

Flash →
RAK WisBlock Starter Kitflashable

nRF52840 + SX1262

Flash →
Seeed SenseCAP T1000-Eflashable

nRF52840 + LR1110

Flash →
Heltec MeshTower V2flashable

nRF52840 + SX1262 + KCT8103L PA

Flash →
muzi works Base Duoflashable

nRF52840 + LR1121

Flash →
Heltec V3/V3.1flashable

ESP32-S3 + SX1262 (no PSRAM)

Flash →
Seeed Wio Tracker L1flashable

nRF52840 + SX1262

Flash →
Seeed XIAO ESP32-S3 + Wio-SX1262flashable

ESP32-S3 + SX1262

Flash →
RAK WisMesh 1W Booster Kitflashable

nRF52840 + SX1262 1W

Flash →
SenseCAP Solar Node P1 / P1-Proflashable

nRF52840 + SX1262

Flash →
Elecrow ThinkNode G4preview

MT7628 + MM6108

Set up →
Heltec HT-HD01-V2preview

MT7628

Set up →

Active bring-up

These boards are actively being brought online. They are visible here for progress tracking, but are not public flash targets yet.

Raspberry Pi Zero 2 Wbring-up

RP3A0, quad-core Arm Cortex-A53

Bring-up in progress

Elecrow ThinkNode M7bring-up

ESP32-S3 + LR1110 + CH390D Ethernet

Bring-up in progress

Roadmap
LILYGO LoRa32 T3-S3roadmap

ESP32-S3 + SX1262/SX1276/SX1280/LR1121 variants

Planned

B&Q Nano G2 Ultraroadmap

nRF52840 + SX1262

Planned

B&Q Station G2roadmap

ESP32-S3 + SX1262

Planned

Not seeing a board you want supported? Let us know in a GitHub issue and help steer what comes next.